Grand General
- Trailer hub cap clip set for newer/late models
- Special designed clip is used on Stemco axle cap to hold regular rear hub cap
- Hold 8" dia. hub cap (20020)
- Set of 3
Chrome front axle cover with 4 notches for newer steel and older aluminum wheels
- Lip: 7/16"
- Notches: 4
- Clips: 4
4 notch chrome front hub cap short lip with hub odometer hole. Included clips for mounting.
Front chrome axle cover 8 23/32" 5 notch short lip hub cap. Fits Newer peterbilt/volvo/ford.
Includes clips for mounting.
- Fits 8-1/2" dia. axle, 8 of 5/8" studs, Also fits Peterbilt 1995 and later
- Size- 1" (H) side wall, Sold by each
- 8" I.D
- Chrome plated steel
- Fits Rear hub caps
- Cone shape
- 8-1/2" dia. axle, 8 of 5/8" studs, also fits "Peterbilt" 1995 up
Rear Axle Cover
- Chrome Plated Steel
- 8 1/2in chrome rear axle cover with 3/4 studs.
- 1 inch Side Walls
- ID: 7-1/4"
- Height: 2-3/4"
- 7-1/4" dia. axle, 12 of 1/2" studs
3/4" standard Push on bolt cover. Used on bumper and frame bolts.
- Chrome plated steel
- Across Flat: 3/4"
- Height: 11/16"
Chrome steel horn cover: round horn cover for 6.5 inch to 7 inch round bell. (measure outside diameter of trumpet to determine correct size.) Mounts with 4 welded on spring clips.
Chrome steel horn cover: round horn cover for 7.25 inch to 7.5 inch round bell. (measure outside diameter of trumpet to determine correct size.) Mounts with 4 welded on spring clips.
Flap weights: 24in chrome bottom flap weight with 3 holes--hardware included. Per each
BOTTOM MUD FLAP PLATE WITH 3 HOLES
- 11.5 Gauge - chrome steel 14 gauge
- Without Backing Plate
- Size: 4" X 24"
- SOLD BY EACH
- Made of 11.5 gauge chrome steel
- Mounting hardware included
- Bottom mud flap plate with 3 studs without backing plate
- 4 Studs on back
- 2" x 24"
- 11.5 gauge - chrome plated steel
- Stainless Steel
- 4" x 24"
- No backing plate
Material | Chrome Plastic |
Features | With flange |
Across Flat | Height | Application |
33mm | 3-3/8" | Push-on |
Bullet Push-On Lug Nut Cover without Flange
Material | Chrome Plastic |
Fits | For most trucks |
Features | Without flange |
6 notch fits at 4, 5, 6 notch hub cap, except all international 6 even notch hub caps
Chrome Plated
Fits 1" long lip |
For wheel with 8-23/32" dia. center hole |
Sold by Each
- Aluminum reflector top plates with DOT-C2 conspicuity tape
- Size- 22 inches in length when measured across, 25-1/2 inches along top edge
- Sold by Pair
Material | Chrome plated steel |
Fits | Hino trucks |
Features | Without flange |
Part No. | Across Flat | Height |
10220 | 40.6mm | 2" |
Part No. | Across Flat | Height |
10269 | 33mm | 3-1/8" |
Concealing your open lug nuts with Grand General's lug nut covers is the easiest and most cost effective way to dramatically change the look of your vehicle. Our wide selection of covers come in many different designs to cater to the OEM look or an aggressive aftermarket style. Made from high quality ABS plastic for a true and secure fit.
Part No. | Across Flat | Height | Application |
10287 | 1-1/2" | 2-1/2" | Push-on |
Material: Chrome Plastic
- For wheel with 8-23/32" dia. center hole
- Sold by each
- For wheel with 8-23/32" dia. center hole
- Sold by each
Size: 5" (W) x 4" (L) Overall Size
Meet DOT's annual inspection requirements. Including complying with §396.17(c)(2) with help from these labels.
Note: On vinyl labels, use indelible permanent ink that will not fade in direct sunlight.
‧Vinyl with protective laminate, 2-ply
This form provides ample room for recording identification data and component conditions. It reflects DOT record keeping criteria for annual vehicle inspections - §396.21. Also includes minimum periodic insepection standards (Appendix G to Subchapter B) on the back of the form to help reinforce DOT vehicle inspection requirements. Durable 100-lb. manila ply helps preserve report
‧3-ply with carbon
- Hardware included
- Width: 24"
- Height 2"
- Material: 14 gauge - stainless steel
- 4 Studs on back
Universal Front Hub Cap in Cove Shape
Lip: 7/16"
Notches: 6
Clips: 4
3" High
Fits 20", 22.5" and 24.5" wheel with 8-23/32" dia. center hole
6 notch fits all 4, 5, and 6 uneven notch hubs
1 1/4" Standard Push On Chrome Nut Cover with Flange
- 1-1/4"width (across flat)
- Height: 2"
3.5 Inch Watermelon Style Glass Lens
Lens Only
Color: Red
- Flush Mount Kit
- No Lens (sold separately)
- 1 Wire
Amber/Red 4 " Round Double Faced Pearl 24-LED Pedestal Light with Chrome Die Cast Housing
- Polycarbonate lens and chrome die cast housing
- 3 wire connection
- 24 LEDs per side, 12V
18 LED Amber Lens/Amber Light Flush Mt Kit | Part Number : 81940
LED | 18 High Power SMD LEDs - 12V |
Size | 3-7/16” dia. x 2-5/8" (H) |
Features | Easy surface mount design |
Material | Sealed polycarbonate lens with stainless steel bezel |
Installation | 12" lead hardwired with three 0.180 bullet plugs |
- Cab light Dark Amber Watermelon Glass Lens
- Chrome Plastic Housing
- 3 1/2 Diameter x 15" L
- 18 gauge wire
- 20 Red LEDs - 12V
- Clear Lens
- Size: 4-1/4" dia. x 1-5/16"(H)
- Sealed polycarbonate lens, reflector and housing
- Hardwired with 3 contact female plug
- 14 gauge Chrome stainless steel
- No Backer Plate
- 3 studs on back design giving the bottom plate a clean finished appearance
- Mounting hardware is included
- 24 inch x 4 inch
Replacement lens for Cab Marker Lights